Bike Noob

Because I'm Always Learning Something New

  • Home
  • About
  • Contact
  • Partners

Archives for April 2009

Time for the MS 150

04.16.2009 by Ray Niekamp // 9 Comments

bpms150Tomorrow’s the day. I’ll take off work early, head home and pack up my bike and stuff. I’ll drive to downtown Austin, where I’ll rendezvous with a bus for Houston. The bike goes on a separate truck, which will take it to the starting line in Houston and secure it overnight. Then, I’ll meet up with my biking and blogging buddy Jared, and we’ll hop the bus for the three-to-four hour ride.

In Houston, there’ll be lots to do. We’ll check into our hotel. We’ll head over to the ride headquarters hotel and take in the bike expo. Our team is hosting a hospitality suite, and it will be our first chance to meet most of the other team members. And we’ll chow down on a spaghetti dinner.

Early to bed, because it’s up at 4 a.m. Saturday. We have to pack our bags and tote them over to the headquarters hotel, where they’ll be put in a team truck for delivery to our halfway stop in LaGrange, Texas. A shuttle bus will run us across I-10 to Tully Stadium, where the ride begins. With luck, we’ll be able to snarf down some breakfast tacos at Tully.

Our team was one of the top fund raising teams last year, so we get the fourth team starting spot. The start is at 6:45 a.m., so we’ll have to be on the bikes and ready to go at that time. It’ll be interesting to see just how the ride organizers herd everyone through the start and keep bikers from crashing into each other left and right.

We’re going to get wet. Depending on which forecast you read, the chance of rain is between 50-80 percent. I hate riding in the rain. But the rest of the day should be nice, with partly cloudy skies and a high in the mid-70sF.

I’m really looking forward to the ride, but I’m feeling some concern about it, too. I haven’t done nearly the prep miles I should have. But I do have that century under my belt, so I’m confident I know how to approach this endeavor. I’ll make it a point to draft more than I did in October, to make my ride a bit easier to handle. And when my bottom starts rebelling during the afternoon, I’ll know how to baby it to get it to the halfway point. First day’s ride is 99.6 miles, according to the ride map. I’ll pedal around the block to get that extra four-tenths of a mile.

I’m counting on being tired enough that night that sleep on a collapsible cot in a sleeping bag under a large group tent shouldn’t be an issue.

On Sunday, the hilly route into Bastrop awaits — I hope. Then it’s another 25 miles to Austin, where Mrs. Noob will be waiting — I hope. I’ll try to post a ride report Sunday evening. I’m pumped.

By the way, I am still soliciting donations to support my ride. It is to raise funds to fight multiple sclerosis, after all. If you’re interested, click here and follow the instructions. Or, you can wait to see if I finish the ride without having to sag in. If I do, you can donate then, if you like. The MS Society will take money for an additional month.

Like this:

Like Loading...

Categories // Rides Tags // MS 150

When to replace a tire

04.13.2009 by Ray Niekamp // 6 Comments

My saga of the hard-to-seat tire got me thinking about tire replacement in general.  As I said, I felt it necessary to buy a new tire because of my upcoming MS 150, and I wanted it in time for last weekend’s 52-miler.

The original tire was new in February.  Because of its kevlar tread, I was hoping for some puncture resistance.  But I don’t think anything could have survived the piece of glass that got this tire.  It was kind of a fluke, too, because the cut was duplicated halfway around the tire.

They weren’t even cuts, exactly — more like a hole, about an eighth of an inch in diameter. When I ran my fingers over them, I could feel a slight bulge right around the hole itself.  It didn’t affect a larger area around the holes.  Because the holes weren’t big, I decided to keep riding on the tire.

The next day, I did a club ride for 38 miles on city streets and rural country roads.  No tire problems.  In fact, I didn’t even think about the tire.  It’s been on several rides since then, for a total of a bit over 200 miles.

When the replacement tire arrived in the mail, I didn’t change it immediately.  I was even considering doing the 52-miler on the damaged tire, since it seemed to be performing fine.  But I happened to be  sitting in the living room reading a bike book, and it said, if the tire is cut, the cut could turn into a puncture.  If it bulges, it will turn into a puncture more quickly.

I went out to the garage and took another look at the tire.  Not only could I feel the bulge, I could see it. That’s when I had my wrestling match with the replacement tire.

I know of some riders who are rather cavalier about their tires.  They’ll ride until they see the tube pushing through the tread, or until it wears down to the threads.

What’s your rule of thumb for replacing your tires?  How far or how long are you willing to ride when you know the tire is less than 100 percent?

Like this:

Like Loading...

Categories // Equipment, Maintenance Tags // tires

Mounting a new tire

04.11.2009 by Ray Niekamp // 12 Comments

I set a record the other night.  It took me a full hour to get a tire mounted on a wheel.

I bought a new tire to replace one that had some severe cuts on the  tread. Since I had a 52-mile ride coming up Saturday, I didn’t want to risk anything — even though the cut tire had seen a good 200 miles on area roads since getting cut in two places by broken glass three weeks ago.

New tires are not as elastic as they get to be with some riding. This one was right out of the mail order box. I put one foot inside the tire, and tried to pull up on it like a rubber band. No give at all.  I turned the tire several times, and pulled each time, to try to add a little bit of stretch to it.

Then, on the wheel. Getting one side into the wheel wasn’t too much of a problem, although even here, I had to patiently work the remaining three inches over the rim. I got the deflated tube inside the tire, then started stretching the other side over the rim.

It was fine for about half the tire’s circumference. Then, it didn’t want to cooperate. Again very patiently (a rarity for me) I worked the bead over the rim bit by bit, and popped it into place. Finally, I had five inches to go. It wouldn’t go. It was as though the tire had reached the limit of any stretch built into it. Whenever I managed to get a small section of bead to pop over the rim, the bead at the other end popped out. It seemed I would be unable to get the tire seated properly.

I know you’re not supposed to use tire levers to mount a tire. There’s some danger they might puncture the tube. I yielded to temptation. The levers worked — sort of. I now had only a three-inch section that refused to mount.

I worked it, and worked it, and worked it. And finally, it happened. The remaining part of the bead popped into the rim. I carefully checked to make sure the tire was seated properly all around, inflated the tire and put it on the bike. Elapsed time: one hour.

I change tires when they flat from time to time, but I haven’t had a lot of experience putting new tires on. They’re very different from changing flats, when the same tire that has miles on it is put back on the wheel. I’ve never had a lot of trouble with those, because use has stretched them out. It’s the brand new tire that was the troublemaker.

These are kevlar tires — I don’t know if that would make any difference or not. But I do remember that the only other time I mounted a brand new tire — one that was not kevlar — I didn’t have anywhere near the trouble.

Any suggestions for making the mounting of a new tire any easier?

P.S.: I was glad today that I did get the tire mounted. I did a hilly 52-mile route from Dripping Springs to Johnson City, Texas, and back again. It was a training ride organized by the Hill Country Ride for AIDS, but I used it as my last hurrah before the MS 150 next weekend.

A lone rider approaches the rest stop in Johnson City.
A lone rider approaches the rest stop in Johnson City.

 

My bike with its new rear tire in Johnson City.  Still with torn bar tape, and with one silver and one white bar plug.
My bike with its new rear tire in Johnson City. Still with torn bar tape, and with one silver and one white bar plug.

I just hope the weather next weekend is better than we had today. It was forecast to get to 80F, but never got above 60, with a chilly northeast wind blowing all morning.

Like this:

Like Loading...

Categories // Equipment, Maintenance, Rides Tags // hills, tires

  • « Previous Page
  • 1
  • 2
  • 3
  • 4
  • 5
  • Next Page »

Get Email Updates

Enter your email address to subscribe to this blog and receive notifications of new posts by email.

Join 259 other subscribers

Categories

  • Accessories
  • Bike fit
  • Bikes
  • Blogging
  • Books
  • clubs
  • Cold weather
  • Community
  • Commuting
  • Components
  • crash
  • cycling
  • Equipment
  • Favorite rides
  • fitness
  • food
  • guest post
  • Heat
  • Injury
  • logs
  • Maintenance
  • Mental
  • Nutrition
  • Odds 'n ends
  • People
  • Poll
  • Racing
  • Records & stats
  • Review
  • Rides
  • running
  • Safety
  • soreness
  • Specialized
  • Technique
  • Technology
  • Tips
  • tires
  • training
  • Travel
  • Uncategorized
  • Home
  • About
  • Contact
  • Partners

Recent Posts

  • Getting Back on the Bike: Road Cycling Tips for Older Cyclists
  • Are BCAAs and EAAs Good for Cycling?
  • How to Fix Numb Toes When Cycling
  • How to Find and Vet a Bike Club
  • Celebrate Pearl Izumi with Big Savings in the Memorial Day Sale

Categories

  • Accessories
  • Bike fit
  • Bikes
  • Blogging
  • Books
  • clubs
  • Cold weather
  • Community
  • Commuting
  • Components
  • crash
  • cycling
  • Equipment
  • Favorite rides
  • fitness
  • food
  • guest post
  • Heat
  • Injury
  • logs
  • Maintenance
  • Mental
  • Nutrition
  • Odds 'n ends
  • People
  • Poll
  • Racing
  • Records & stats
  • Review
  • Rides
  • running
  • Safety
  • soreness
  • Specialized
  • Technique
  • Technology
  • Tips
  • tires
  • training
  • Travel
  • Uncategorized

Archives

  • May 2024
  • December 2023
  • November 2023
  • March 2022
  • October 2020
  • November 2018
  • May 2018
  • September 2017
  • November 2016
  • October 2016
  • January 2016
  • July 2015
  • June 2015
  • May 2015
  • April 2015
  • March 2015
  • February 2015
  • January 2015
  • December 2014
  • November 2014
  • October 2014
  • September 2014
  • August 2014
  • July 2014
  • June 2014
  • May 2014
  • April 2014
  • March 2014
  • February 2014
  • January 2014
  • December 2013
  • November 2013
  • October 2013
  • September 2013
  • August 2013
  • July 2013
  • June 2013
  • May 2013
  • April 2013
  • March 2013
  • February 2013
  • January 2013
  • December 2012
  • November 2012
  • October 2012
  • September 2012
  • August 2012
  • July 2012
  • June 2012
  • May 2012
  • April 2012
  • March 2012
  • February 2012
  • January 2012
  • December 2011
  • November 2011
  • October 2011
  • September 2011
  • August 2011
  • July 2011
  • June 2011
  • May 2011
  • April 2011
  • March 2011
  • February 2011
  • January 2011
  • December 2010
  • November 2010
  • October 2010
  • September 2010
  • August 2010
  • July 2010
  • June 2010
  • May 2010
  • April 2010
  • March 2010
  • February 2010
  • January 2010
  • December 2009
  • November 2009
  • October 2009
  • September 2009
  • August 2009
  • July 2009
  • June 2009
  • May 2009
  • April 2009
  • March 2009
  • February 2009
  • January 2009
  • December 2008
  • November 2008
  • October 2008
  • September 2008
  • August 2008
  • July 2008
  • June 2008
  • May 2008
  • April 2008
  • March 2008
  • February 2008

Copyright © 2026 · Modern Studio Pro Theme on Genesis Framework · WordPress · Log in

Go to mobile version
%d